Graham Field Bathroom Aids 6482ER 2 User Manual

6482R-2/6482ER-2: DELUXE TOILET SEAT RISER WITH ARMRESTS  
ASSEMBLY & OPERATION INSTRUCTIONS  
PLEASE SAVE THESE INSTRUCTIONS FOR FUTURE USE  
Info: The most current version of these instructions can be found online at www.grahamfield.com  
Tools required: Phillips or blade screwdriver  
WARNING: Important! Read and understand these instructions  
before installing or using the Toilet Seat Riser. If you do not under-  
stand any part of these warnings, cautions or instructions, contact  
a healthcare professional for direction in the use of this product. If  
the toilet seat riser is not properly assembled and installed, person-  
al injury and damage to the toilet seat riser could result.  
WARNING: If components are damaged or missing, contact your  
6482R-2 assembled  
dealer immediately. DO NOT use substitute parts. Use only Lumex  
replacement parts. Non-Lumex replacement parts could cause per-  
sonal injury and damage to the toilet seat riser.  
WARNING: This product has a weight limit of 300 lb.  
WARNING: GF Health Products, Inc. assumes no responsibility for  
any damage or injury caused by improper assembly, installation or  
use of this product.  
INSTALLATION  
1. Remove toilet seat riser, hardware, and armrests from carton and protec-  
tive packaging.  
6482ER-2 assembled  
“R” on armrest socket  
locking button  
2. Install the armrests with the following steps:  
a. Identify the right and left armrests by the R (Right) and L (Left)  
stamped into armrest ends.  
b. Note that each toilet seat riser armrest socket is also stamped with an R  
or L, as shown at right. Insert each armrest marked with R or L into the  
socket with the corresponding letter.  
c. Push each armrest into its sockets until it clicks into place.  
armrest  
toilet seat riser  
d. Ensure locking buttons protrude fully from holes. Pull on armrests  
slightly to test proper installation. If loose, repeat step c.  
right armrest shown installed  
(shown upside down)  
mounting holes  
3. At the toilet, lift the cover plates at top rear toilet bowl rim, exposing the  
bolts holding the seat and lid to the toilet bowl.  
4. Use a Phillips or blade screwdriver, whichever is appropriate, to unscrew  
toilet seat bolts by turning counterclockwise.  
5. Remove the toilet seat and lid from the toilet bowl and set them aside.  
6. Place the toilet seat riser over the toilet bowl rim so that the toilet seat  
riser mounting holes align with the toilet rim holes.  
7. Place the toilet seat and lid on top of the toilet seat riser so that the seat/  
lid holes align with the riser and rim holes.  
6482ER-2, one arm attached  
(shown upside down)  
8. Install a washer on one of the long bolts included in the box and insert it  
through the top of the toilet seat lid, toilet seat riser, and toilet bowl rim.  
wing  
nut  
9. Place a washer and wing nut on the end of the long bolt that protrudes  
through the bottom of the toilet bowl.  
bolt  
washers  
hardware  
6486R-2-INS-LAB-RevA11  
1
 

Graco Inc Paint Sprayer 208008 User Manual
Haier Washer HMS1002A User Manual
Honeywell Door RCWL3501A User Manual
Honeywell Thermostat CT3451 User Manual
Hotpoint Dishwasher DWF40 User Manual
HP Hewlett Packard Computer Monitor A6B85A8ABA User Manual
Humminbird Fish Finder 300 series User Manual
Husqvarna Blower 225B User Manual
Husqvarna Lawn Mower 532 42 41 94 User Manual
iHome Headphones IB24 User Manual